高工作电压小电压检验装置仪（耐电弧焊接检验装置仪）-（确定机管控）

High voltage low current tester (arc resistance tester) - (computer control)

商商品编码称：耐电弧试验机

Product name: electric arc resistance tester

成品产品编号：NDH-A

Product model: NDH - A

提供标淮：GB/T 1411-2002《物质耐压物料耐高偏低电流大小电弧焊接击穿的冲击试验》（符合IEC  61621-1997）及ASTM D495等标准规定的耍求构思研制的，并非常符合IEC 149、UL 746A等耐压试验具体方法

Meet the standards: GB/T 1411-1411 "solid insulating material resistant to high voltage low current arc discharge test" (equivalent to IEC 61621-1997) and the requirements of standards such as ASTM D495 design and manufacturing, and conform to the IEC 149, UL 746 a test method, etc

一 概述

一An overview of the

具体应用规模及作用：

本应力测试软件机是遵循用作高压电机、电嚣和家里用的电嚣等业内的电工作业用朔料、树酯胶和隔绝性漆等隔绝性素材的耐焊弧功效参数评比，主用作物质隔绝性素材如：朔料、聚酰亚胺膜、树酯、黑云母、卫浴陶瓷、玻璃钢、隔绝性油、隔绝性漆、纸箱等媒介的耐焊弧功效参数测试软件；

本试验报告机由计算的机把控好工作，能否显视到现阶段状况测试情况下及测试周期，测试收尾后并保持到现阶段状况测试数据报告，并可打印图片.的标准测试评估报告。

Main scope of application and features:

This machine is in accordance with the applied in motor, electrical appliances and household appliances and other industries with varnish insulation materials such as plastic, resin adhesive and the arc resistance evaluation, the main used for solid insulating material such as plastic, film, resin, mica, ceramic, glass, insulating oil, insulating paint, such as cardboard medium arc resistance test;

This testing machine controlled by computer operation, can display the current experimental condition and experimental time, after the experiment, and save the current experimental data and can be printed. Standard experiment report 

二 功能特点

1 该机为横竖合一构成，下部分为方法软件，顶部为检验箱。

2 本护肤品使用*新智力管控系统，用首选过程（IEC或ASTM）可电脑自动进行试验装置，并在笔记本上出现测试具体步骤和导致。

3 **能稳定，抗要素本事强，测试软件定位精度就越高。

二：Functional features：

1 this machine is up and down a body structure, lower for the operating system, the upper part of test cases.

2 this product USES the latest intelligent control technology, through the selection process (IEC) or ASTM test can be automatically, and displayed on the computer and the test process and results.

3 good safety performance, strong anti-interference ability, high test precision. 

三 主要技术参数

1 电弧焊接通断事件误差值：低于 ±10ms

2 调压器储存量：2kVA

3 额定功率测试电阻：12.5kV

4 测试交流电压要求：±3%

5 电流值控住精密度较：±10%  电压电流衡量定位精度：1.5%

6 探针对试件负担：（0.5±0.05）N

7 参比电极建材：钨棒

8 参比电极距里：（6.35±0.1）mm（IEC）

               （6.0±0.1）mm（ASTM）

9 应用生态平均温度：（23±2）℃

10 采用生态环境温度：（50±5）%

11 电：220V±5%  50Hz  10A

12 测试    的办法：   行业标准/美标/10 mA 联续/20 mA 重复/30 mA不间断/40 mA陆续

13 可靠性试验系统程序如表：

Three main technical parameters：

Error: 1 arc on-off time less than plus or minus 10 ms

Transformer capacity: 2 kva

3 test voltage rating: 12.5 kV

4: test voltage accuracy + / - 3%

5 current control accuracy: plus or minus 10% current measuring accuracy: 1.5%

6 electrode pressure on sample: (0.5 + 0.5) N

7 electrode materials: tungsten rods

8 electrode distance: 6.35 + / - 0.1 mm (6.0 + 0.1) mm (IEC) (ASTM)

9 using the environment temperature (23 + 2) ℃

10 use environment humidity: (50 + 5) %

Power supply: 220 v + 5% for 50 hz 10 a

Test method: beautiful mark / 10 gb / 30 mA mA continuous / 20 mA continuous/continuous / 40 mA continuous

13 test procedure is as follows:

Procedures section of the arc current

MA arc on-off time s the program s test total duration time s

IEC 61621 ASTM D495

1 1/8 10 s on 7/8 s broken 1/4 7/4 break 60 s 60 s

2 10 1/4 "s pass 3/4 s 1/4 3/4 break 60 s 120 s

3 to 10 1/4 "s make a quarter s break a quarter of a quarter break 60 s 180 s

4 consecutive 10 to 60, 240

5 20 consecutive 60, 300

30 consecutive 6 to 60, 360

7 consecutive 40 to 60, 420 

四  配置

Four configuration：

Serial number name number note

01 arc resistance tester

02 a electrode system

03 electrode bearing a set

04 a set of power cable

05 ground put a rod

06 milliammeter current one

7 a set of computer measurement and control software

08 specimen holder a

09 electrode distance standard 2 blocks

Standard 2 blocks of 10 Angle

11 ceramic pieces 2 pieces

12 one brand inkjet printer

13 1 computer brand

14 1 instruction manual

15 1 certificate

五 成品型號：

NDH-A    耐弧光耐压仪-微机保持

NDH-B    耐焊弧校正仪-触屏屏的控制

Five product model:

NDH - A arc resistance tester - microcomputer control

NDH - B arc resistance tester - touch screen control
ASTMD495耐高压低电流电弧放电试验机详情可以随时来电咨询！